What are the details to pay attention to when processing marble countertop panels?

The application of stone countertops is increasing. It is not only widely used in hotels, and commercial offices, but also in home decoration, especially on countertops and kitchen cabinets for televisions, coffee tables, and various furniture. It is deeply loved by home decoration. Although stone countertop panel products are not products with complex processing techniques, there are many details to pay attention to in the processing of stone countertop panels. Attention should be paid to the details when processing the countertop panel. If not paid attention during processing, the quality of the processed countertop panel will be poor, seriously affecting the decorative effect of the countertop panel. Therefore, the processing details of the countertop panel cannot be neglected during processing, and special attention should be paid. There are several specific points:

(1)  The thickened edge should be consistent with the color and texture of the countertop panel

This requirement is mainly controlled during cutting and bonding. The bridge cutter should pay attention to selecting materials for the thickened strip and the platform panel on the same large plate, and cut the plate at the same position. If it is necessary to cut another large board due to insufficient size, the color and texture must be aligned, and the board must be cut at areas where the color and texture are the same. After cutting the adhesive strip and the table panel, number them according to the set and place them together. The adhesive worker of the thickened strip first checks the color and texture of the adhesive strip and the countertop panel before bonding, and then confirms that the color and texture of the adhesive strip are the same before bonding.

(2)  The consistency of color and texture between the water deflector and the countertop panel

When cutting the table panel with a water baffle, follow the requirements of (1), number it according to the set, and place it according to the set. When arranging boards, the board arranging staff carefully arrange the boards according to the set, inspect, color adjust, number them, and mark the direction of edge grinding.

(3)  The size of the adhesive gap between the thickened strip and the countertop panel

Before bonding, check the color of the thickened strip and the countertop panel to ensure that the color and texture of the thickened strip and the countertop panel are consistent before bonding. Otherwise, once bonded together, if the color and texture difference between the thickened strip and the countertop panel is too large, it will greatly affect the decorative effect. A large number of clips are used for the bonding of the countertop panel, to clamp the thickened strip with the countertop panel, increasing the bonding force between them, reducing the gap between the thickened strip and the countertop panel, ensuring that the bonding gap is small and the bonding effect is good; When the bottom surface of the countertop panel has severe edge chipping, mechanical thickness adjustment or manual grinding can be used to eliminate the edge chipping and reduce the adhesive gap.

(4)  Color of the adhesive gap between the thickened strip and the countertop panel

The gluing process is carried out by a professional gluing master, who adjusts the gluing according to the main color of the stone countertop panel. Strictly follow the glue ratio when adjusting the glue. After adjusting the adhesive, first try to bond one piece. After curing for 1 hour, scrape off the surface to be bonded and check if the color of the adhesive meets the requirements. If the color of the adhesive meets the requirements, it can be bonded in large quantities. The amount of glue prepared each time should not be too much, it is best to prepare according to needs. Do not use the prepared glue overnight. When bonding, clean the bonding surface carefully to ensure that it is free of dust, dirt, and other substances that may affect the color of the adhesive. When the color of the adhesive at the bonding joint is incorrect, use a single-sided blade to remove the adhesive and re-mix the adhesive for repair.

(5)  Quality of adhesive repair for the countertop panel

As a stone product that provides close contact with human vision, the quality of the marble countertop panel is determined by the quality of the adhesive, as well as the price, grade, and grade of the marble countertop panel, due to the many cracks on the surface of the marble. In addition to careful repair during the processing of the large panel, the quality of adhesive repair for the marble panel should also be handled carefully during the processing. If the adhesive repair is not beneficial, it should be removed and repaired again. The adhesive repair of the countertop panel should ensure that the brightness of the repaired area is the same as that of the panel surface; There are no visible traces of repair at the adhesive repair site; The traces of adhesive repair are not obvious when viewed from the side light; The color of the area to be repaired is consistent with the main color tone of the stone; There is no obvious tactile sensation when touching the area to be repaired on the countertop; The adhesive at the area to be repaired on the countertop does not change color; There is no adhesive shrinkage or depression at the area to be repaired on the countertop.

(6)  The quality of edge grinding on the countertop panel

The best way to achieve mechanical edge grinding is to grind the edges of the table panel. If mechanical edge grinding cannot be achieved, it can be done manually by employees with high polishing skills after forming with forming wheels.

(7)  Color and texture requirements for panels with splicing relationships

Before cutting the color and texture of the panel with splicing relationships, a material plan should be made. The bridge-cutting worker should strictly follow the material plan of the panel and cut it according to the set and number; The employees who arrange the boards check the colors and textures according to the set, promptly identify problems, and replace parts with different colors and textures. Number the boards that have been properly arranged and passed the inspection according to the set number, and place them in the order of the set for processing in the next process.

(8)  Strengthen the strict inspection and inspection of the countertop panel

The processed tabletop is arranged, inspected, and inspected according to the set. Focus on checking the surface adhesive quality of the countertop panel and whether there are any abrasions or scratches on the surface; Focus on checking whether the color and texture of the thickened strip on the countertop are the same as those on the countertop; The quality and effectiveness of the adhesive seam, color, and effect between the thickened strip and the countertop panel; The straightness and flatness of the edge grinding; Number and package the water blocking panel according to the set.

Share on facebook
Facebook
Share on twitter
Twitter
Share on linkedin
LinkedIn
sntstone

Don't go away, more surprises!!

Product Inquire

We will contact you within 1 working day, please pay attention to the email with the suffix “@sntstone.com”